5/6/2023 0 Comments T1 media converter![]() When used in the 14-Module power-redundant Powered Chassis with any combination of AC and DC power supplies, the installed modules are powered via the 5VDC chassis connector.įlexPoint unmanaged media converters are easy to use and provide dependable fiber connectivity in Enterprise and Government networks around the world. The RAD-SuperMoon has a programmable membrane label that shows network status and allows setting the 1000BASE-T1 PHYs to master mode, slave mode, or. Standalone modules can also be powered by attaching an external DC power supply (18-60VDC). The RAD-SuperMoon also offers a pure media converter mode, which disables encapsulation of messages and allows connections between media of differing bit rates, buffering frames as needed. They can also be rack-mounted in a 5-Module shelf or in a high-density 14-Module, power-redundant Powered Chassis.įlexPoint modules installed in the 5-Module shelf or used as standalone devices can be powered by an external AC to DC power adapter, or through the 5VDC chassis connector. The LEDs report the availability of power, connection status, diagnostic or loopback modes of operation and the detection of all 1’s by the fiber and UTP ports.įlexPoint modules can be mounted utilizing optional wall-mounting hardware or with DIN-rail mounting brackets. The FlexPoint T1/E1 features descriptions of the LED indicators on the label for easy in-the-field configuration, installation and maintenance. Dry contact relay option allows a separate T1/E1 alarm circuit to be notified when a loss of power is detected. Local loopback validates connectivity to local T1/E1 lines, while remote loopback validates the entire fiber segment from one unit without having to make adjustments on both ends. With over 30 years in business, Omnitron Systems designs and manufactures Network Interface Devices, media converters and multiplexers that are deployed in LAN and WAN networks worldwide. Multimode fiber models support distances of up to 5km, and single-mode fiber models support distances of up to 60km.ĭiagnostic features include local loopback, remote loopback and all 1’s insertion (AIS) modes for the copper or fiber segments. The fiber port operates at 1310nm and supports SC or ST connectors. DIP-switches provide easy configuration of T1/E1 line codes and line build-out.Ī crossover switch makes it simple to connect the FlexPoint T1/E1 converter to PBXs or CSUs and eliminates the need for a crossover cable. The converter also supports AMI, B8ZS and HDB3 line codes. T1/E1 media converters operate in pairs, providing distance extension over fiber.ĭesigned as a transparent repeater, the FlexPoint T1/E1 supports standard T1, E1 and Primary Rate Interface (PRI), voice or data. Thus, the 100BASE-T1 Media Converter NXP is the ideal solution for working quickly and efficiently with the new 100BASE-T1 technology without the hustle of extra- wiring, customized connectors, and vendor-specific tools.The FlexPoint T1/E1 media converter provides standard T1 (1.544Mbps) or E1 (2.048Mbps) copper to fiber conversion and can be used to extend the demarcation point between service provider and networking equipment. The device can be coupled with any hardware or software tool that runs on standard Ethernet with an RJ-45 connector. No extra hardware or software is needed to connect the device with a PC or a Laptop. With the in-built status LEDs, the operation of the device is transparent and aids the tester to detect Link up and data transmission visually. The device is capable to function in a variating temperature range from -40 Celsius to +80 Celsius. The galvanized sheet steel with black powder coating housing makes it robust with IP20 protection. Its design makes it portable and easy to install in test racks. It comes with an automotive grade MQS connector (Power and 100BASE-T1) and a standard Ethernet RJ-45 connector. The device communicates with standard Ethernet through an RJ-45 connector. No customized driver is needed to interact with our 100BASE-T1 Media Converter NXP. ![]() A massive stainless-steel housing, coupled with DIP switches for ease of configuration enables the user to interact with the converter, effortlessly. The device features bi-directional conversion between Standard Ethernet (100BASE-TX) and Automotive Ethernet (100BASE-T1). The conversion takes place on a Physical Layer with the highest proven reliability.īy using the NXP TJA1100_MRA4 PHY, we ensure a trustworthy and effective tool to our customers that are looking for a cost-efficient, quick and manageable solution for their testing requirements, with no latency and no packet loss. ![]() In the conversion, no packets are stored or modified. The 100BASE-T1 Media Converter NXP establishes a direct point-to-point conversion between automotive ECU’s using 100BASE-T1 (100 Mbit/s Fullduplex, with 1x Unshielded Twisted Pair (UTP) cable) and any standard Fast Ethernet (100 Mbit/s, 100BASE-TX) device with an RJ-45 connector.
0 Comments
Leave a Reply. |